NACE-CIP1-001 exam is a hot NACE certification, if you want to get your CIP Level 1 certification, Passquestion team provides you the latest Coating Inspector CIP Level 1 NACE-CIP1-001 Practice Test Questions for your best preparation, all questions and answers are collected from real test and verified by experts and successful candidates. If you study well, we ensure you can pass your NACE-CIP1-001 Coating Inspector Level 1 exam easily.

CIP Level 1 certification is designed for Coating Inspectors responsible for performing and documenting basic and non-destructive inspections of liquid coatings applied by brush, roller or spray to steel surfaces under the supervision of a level 2 in a shop setting or level 3 inspector when working in a shop or field setting.

CIP Level 1 NACE-CIP1-001 Learning Objectives:

Give examples of corrosion fundamentals such as properties of a coating, coating classification and modes of protection
Recognize coating types and curing mechanisms
Recall coating specifications including service environments and coating life cycle
Differentiate surface preparation equipment, methods, and standards for abrasive blasting, solvent cleaning, and power and manual tool cleaning
Differentiate coating application by type, including brush, roller, mitt, and conventional and airless spray
Demonstrate inspection procedures
Describe the role of the inspector –as it applies to safety, ethics, conflict prevention, and decision making
Test for environmental or ambient conditions and nonvisible contaminants
Utilize non-destructive test instruments such as wet-film and dry-film thickness gauges and low and high voltage holiday detectors
Measure surface profile using replica tape and anvil micrometers, surface profile comparators, and digital surface profile gauges
Identify quality control issues, recognizing design and fabrication defects and coating failure modes
Utilize Safety Data Sheets (SDS) and product technical data sheets
Demonstrate the purpose and content of Logbook and report documentation 

Requirements for CIP Level 1 Certification

Share some CIP Level 1 NACE-CIP1-001 Practice Test Questions:

1.You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
A. Break the blisters to see what's inside
B. Document the problem and advise the Contractor and Owner's representative
C. Document the problem and advise the Contractor
D. Extract any liquid that may be inside the blister and send it to the lab for further analysis
Answer: B

2.Dew point is the temperature at which
A. water freezes.
B. humidity decreases
C. condensation occurs.
D. the air is saturated.
Answer: C

3.If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
A. dry film thickness (DEI) measurement.
B. wet film thickness (WFT) measurement.
C. blotter test for the presence of oil and water.
D. vial lest.
Answer: C

4.Upon arrival of coating materials, the inspector should 
A. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations. 
B. observe and document the amount of material and batch numbers. 
C. observe aryl document that the applicator WFT at regular intervals during application. 
D. observe and document time frame and environmental conditions between each coat.
Answer: B

5.Relative humidity is 
A. a measure of the amount of moisture in the air compared to saturation level. 
B. a measure of the amount of moisture in the air compared to the air temperature. 
C. the lowest temperature at which moisture forms on a steel surface. 
D. the highest temperature at which moisture forms on a steel surface.
Answer: A

6.Galvanic corrosion occurs on which of the following substrates: 
A. Concrete 
B. Fiberglass Reinforced Plastic 
C. Metal 
D. Wood
Answer: C

7.When applying Thermal Spray Coatings the specification is most likely to refence: 
A. SSPC PA 2 
B. NACE SP 0178 
C. NACE SP 0188 
D. SSPC-CS 23.00/AWS C2.23/NACE No. 12
Answer: D

8.What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
A. 1 cm (.39 inch) 
B. 2.5 cm (1 inch) 
C. 6.35 cm (2.5 inch) 
D. 2.5 millimeters (.10 inch)
Answer: B