If you are thinking about appearing for the HCIA-5G-RAN V3.0 H35-480_V3.0-ENU exam, then PassQuestion H35-480_V3.0-ENU HCIA-5G-RAN V3.0 Exam Questions are made for you. It will help you to achieve the HCIA-5G-RAN Certification exam with good grades. PassQuestion provides the best-designed quality H35-480_V3.0-ENU HCIA-5G-RAN V3.0 Exam Questions that can help you to achieve the Huawei H35-480_V3.0-ENU exam without any problem. You will get the real questions of the H35-480_V3.0-ENU test with their expertly verified answers from all the topics to help you enhance your knowledge in the exam. You are guaranteed to pass your H35-480_V3.0-ENU HCIA-5G-RAN V3.0 exam successfully in your first attempt.

HCIA-5G-RAN Certification

Holding HCIA-5G-RAN certification proves you have the capability of independently completing the commissioning and deployment of Huawei 5G radio networks, performing routine operations and onsite maintenance for Huawei 5G wireless base stations, and handling Huawei 5G radio network faults under the guidance of others.

HCIA-5G-RAN V3.0 Exam Details

Certification: HCIA-5G-RAN
Exam Code: H35-480
Exam Name: HCIA-5G-RAN V3.0
Language: ENU
Exam Format: Single answer, Multiple answer, True-false question
Exam Cost: 200USD
Exam Duration: 90 mins
Pass Score/Total Score: 600/1000

Exam Contents

The HCIA-5G-RAN V3.0 exam covers:

• 5G Principle Basics      25%
• 5G Base Station Product Basics      30%
• Overview of Basic 5G Wireless Network Features       20%
• 5G Wireless Network Test and Problem Analysis      25%

Knowledge Points

5G Principle Basics (25%)

• 5G Overview
• 5G Network Architecture and Interface
• Introduction to the 5G Physical Layer 
• Typical 5G Processes

5G Base Station Product Basics (30%)

• Basics of 5G Base Station Hardware
• Basic Operations on 5G Base Stations
• Software Commissioning for 5G Base Station Equipment

Overview of Basic 5G Wireless Network Features (20%)

• NSA Networking based on EPC
• Mobility
• Scheduling
• MIMO
• Power Control

5G Wireless Network Test and Problem Analysis (25%)

• RF Tool Introduction
• 5G Single Site Verification
• 5G Service Test

View Online HCIA-5G-RAN V3.0 H35-480_V3.0-ENU Free Questions

Which of the following devices is used to implement service slicing on the 5G RAN side?
A.Antenna
B.BBU
C.AAU
D.RRU
Answer: B

What is the required distance between a CPE and a gNodeB in a 5G network test?
A.Less than 10m
B.Greater than 5m
C.Less than 5m
D.Greater than 10m
Answer: B

According to 5G eMBB service requirements, which of the following is the minimum rate required for network edge coverage?
A.1 Gbps
B.100Mbps
C.1Mbps
D.10Gbps
Answer: B

During 5G single site verification, you only need to test the user access and rate. Other test items are analyzed in drive tests.
A.True
B.False
Answer: B

During a 5G service test, an NSA UE connects to the Probe and then accesses a 4G cell. It is found that the cell does not deliver B1 measurement configurations. Which of the following is not a possible cause for this?
A.The UE does not support EN-DC.
B.The NSA switch is not turned on.
C.Neighboring LTE cells and SCGs are not configured.
D.The B1 threshold is too high.
Answer: C

Which of the following messages is the first message sent by a gNodeB to an AMF?
A.NGAP_UL_NAS_TRANSP
B.RRC_SETUP
C.NGAP_INIT_CONTEXT_SETUP_RSP
D.NGAP_INIT_UE_MSG
Answer: C

During a 5G test, a portable computer is directly connected to the LAN port of the Huawei CPE through a network cable to obtain a dynamic IP address for communication.
A.True
B.False
Answer: B

Which of the following can be used to check whether an antenna is reversely connected during NR single site verification?
A.Fixed-point CQT
B.DT around the site
C.Transmission test
D.VSWR test
Answer: C